IntelCAD team

PCB Annular Ring: Size, IPC Classes and Design Rules

PCB annular ring explained: how to calculate it, IPC Class 2 vs Class 3 breakout rules, pad and drill sizing, teardrops, and how DFM catches thin rings.

Close-up of PCB through-hole vias with copper annular rings, one off-center hole leaving a thin ring on one side

Short answer: A PCB annular ring is the ring of copper left around a drilled hole, between the edge of the hole and the outer edge of its pad. You calculate it as (pad diameter minus hole diameter) divided by 2. It has to survive drill wander and layer misregistration, so size pads with your fabricator’s minimum ring plus a manufacturing allowance, add teardrops where traces meet small pads, and check which IPC class your board is built to, because Class 3 requires a full ring while lower classes tolerate some breakout.

Close-up of PCB through-hole vias with copper annular rings, one off-center hole leaving a thin ring on one side
Close-up of PCB through-hole vias with copper annular rings, one off-center hole leaving a thin ring on one side

What is an annular ring?

Every plated hole on a board, whether it is a via or a through-hole component pin, sits inside a copper pad called a land. After drilling, what is left of that land around the hole is the annular ring. “Annular” just means ring-shaped.

The ring does three jobs. It gives the plating in the hole barrel something to bond to on each layer, it forms the electrical joint between the barrel and the trace or plane that connects to it, and on component holes it gives solder a surface to wet. If the ring is too thin, or the drill breaks out of the pad entirely, the connection can be weak, open or unreliable under thermal cycling.

There are two kinds to keep apart:

How to calculate annular ring size

The basic formula is simple:

Annular ring = (pad diameter − hole diameter) / 2

For example, a 0.6 mm pad with a 0.3 mm hole has a nominal annular ring of 0.15 mm on every side.

That number is the best case. Real boards lose part of it to three effects:

  1. Drill position tolerance. The drill never lands exactly on the pad center.
  2. Layer-to-layer registration. Inner layers shift slightly against each other and against the drill during lamination.
  3. Hole size. The drill bit is larger than the finished hole, because plating then builds up inside the barrel. Fabricators usually choose the drill, so give them the finished hole size you need.

Because of this, designers work backwards from the minimum ring they must guarantee. A common method, based on the IPC-2221 approach, is:

Minimum pad diameter = maximum finished hole + 2 × minimum annular ring + fabrication allowance

The fabrication allowance covers the drill and registration error for your fab’s process. Its value depends on the shop and on board complexity, so take it from your fabricator’s capability sheet rather than from a generic table. Many fabs publish a minimum annular ring for vias and for component holes; use that as the floor, not the target.

IPC Class 2 vs Class 3 annular ring requirements

The acceptance rules for annular rings on finished boards come from IPC-6012 (performance and qualification for rigid boards) and are inspected with the help of IPC-A-600 (acceptability of printed boards). The key difference between classes is how much breakout is allowed, meaning how far the hole may run outside the pad.

Exact values change between revisions and between external and internal layers, so confirm the numbers in the revision your purchase order calls out. In practice, if your drawing says “IPC-6012 Class 3”, your pads need noticeably more margin than a Class 2 consumer board with the same drill.

Tangency is the edge case where the hole just touches the outer edge of the pad, leaving zero ring at one point. Whether that is acceptable depends on class; for Class 3 it is a reject.

Annular ring design rules that prevent breakout

These rules keep your rings intact without wasting board space:

  1. Start from the fab’s capability sheet. Use its minimum ring for plated holes and add margin, especially on dense inner layers.
  2. Specify finished hole sizes, not drill sizes, in your drill table and fab notes. Our Gerber files guide covers what belongs in the drill and fab package.
  3. State the IPC class on the fab drawing. The fabricator then knows which ring and breakout criteria to build and inspect to.
  4. Add teardrops where traces join small via pads. A teardrop widens the junction so that, if the drill does wander, the trace is still connected. This matters most on Class 2 boards that accept some breakout.
  5. Give inner layers extra margin. Registration error stacks up with layer count, and inner rings cannot be reworked.
  6. Be careful with non-functional pad removal. Removing unused inner pads helps drilling and signal integrity, but check with your fab before removing them on high-reliability boards.
  7. Treat microvias separately. Laser-drilled microvias in HDI builds use capture and target pads with their own rules; see our guide to blind and buried vias.
  8. Watch via-in-pad and thermal vias. Filled and plated-over vias still need a sound ring under the cap. Our via in pad guide and thermal vias guide cover the specifics.
  9. Keep solder mask openings consistent with the pad, so a thin external ring is not also covered or exposed unevenly. See our PCB solder mask guide.

Common annular ring mistakes

Where AI and DFM checks help

Annular ring problems are geometry problems, and they hide in volume: a board can have thousands of vias, and the one with a too-small pad is usually in the densest corner. A rule-based DRC only catches what its settings describe. An AI-assisted DFM pass compares every pad and hole against your fabricator’s limits and the IPC class on the drawing, checks inner and outer layers separately, flags trace junctions that would open after breakout, and points out footprints that reuse the wrong pad stack.

That is the IntelCAD approach: catch thin rings and mismatched pad stacks during design, together with the rest of your PCB DFM and design review checklist, before the boards are built.

FAQ

What is an annular ring on a PCB?

An annular ring is the ring of copper pad left around a drilled hole on a PCB. It connects the plated hole barrel to the traces or planes on each layer.

How do you calculate annular ring size?

Subtract the hole diameter from the pad diameter and divide by two. A 0.6 mm pad with a 0.3 mm hole has a nominal 0.15 mm annular ring.

What is annular ring breakout?

Breakout happens when the drilled hole runs partly outside its pad, so part of the ring is missing. It is caused by drill wander and layer misregistration.

What is the difference between IPC Class 2 and Class 3 annular ring requirements?

Class 2 accepts limited breakout as long as the conductor connection stays within limits. Class 3 accepts no breakout and requires a minimum ring all the way around the hole.

How can I prevent annular ring problems?

Size pads from your fab’s minimum ring plus allowance, specify finished hole sizes and the IPC class, add teardrops at small pads, and run a DFM check against your fab’s real limits.

Next step

Want every pad and hole on your board checked against your fab’s annular ring limits before you order? Start Your Design with IntelCAD for AI assisted PCB design and manufacturability checks.

Design your next board by describing it.

Start Your Design