IntelCAD team

PCB Solder Mask Guide: LPI vs Dry Film, Colors and Pads

PCB solder mask guide: LPI vs dry film, colors, SMD vs NSMD pads, tented vias, openings and dams, and how AI/DFM catches mask errors before fab.

Top-down PCB with green solder mask, exposed copper pads and vias in a clean technical diagram

Short answer: PCB solder mask (also called solder resist) is the polymer coating that covers copper everywhere except pads, vias and other openings you define. Most production boards use liquid photoimageable (LPI) solder mask; dry film is the common alternative for thick or high-reliability builds. You choose color, SMD vs NSMD pad definition, dam width, tented or plugged vias, and expansion so paste, assembly and fab all stay in one process window.

Top-down PCB with green solder mask, exposed copper pads and vias in a clean technical diagram
Top-down PCB with green solder mask, exposed copper pads and vias in a clean technical diagram

What is solder mask on a PCB?

A solder mask in PCB fabrication is a thin dielectric film applied over etched copper. It stops solder bridges, protects copper from oxidation and handling, and sets the visual color of the finished board. When people ask what is solder mask, the practical answer is: the layer that tells the assembler where paste and parts are allowed to land.

Solder mask pcb artwork lives in its own Gerber (or ODB++) layers, usually top and bottom. Clearances, dams and openings in that artwork decide whether fine-pitch BGAs solder cleanly or whether paste shorts neighboring pads. Treat the solder resist PCB layer as a design decision, not a default green overcoat. It belongs in the same PCB DFM pass as drill sizes and copper clearances.

LPI vs dry film solder mask

Two process families dominate production solder mask pcb builds:

TypeHow it is appliedStrengthsTradeoffs
Liquid photoimageable (LPI) solder maskLiquid ink coated, dried, exposed through artwork, developedFine openings, good for dense SMD, industry default, many colorsThickness can vary at copper edges; swell/shrink with process
Dry film solder maskLaminated photopolymer film, exposed and developedMore uniform thickness, useful for thick copper or harsh environmentsCoarser resolution than modern LPI; fewer shops stock every color

Liquid photoimageable solder mask (LPI) is what most fabricators mean when they quote a standard solder mask. Dry film solder mask still shows up on RF, power and high-reliability builds where thickness control matters more than the smallest opening. Ask your fab which LPI solder mask chemistry and thickness they run before you assume a 0.05 mm dam will survive their process.

Solder mask colors and visibility

Solder mask colors are not only branding. Green remains the default because human and AOI inspection contrast well against copper and white silkscreen. Blue, red, black, white, purple and yellow are all common. Matte black and white can reduce glare for cameras or improve cosmetics, but they can hide solder joints or silkscreen errors if contrast is poor.

Pick solder mask color with assembly and inspection in mind, then lock it in fab notes the same way you lock a PCB stackup. Do not change color late without rechecking silkscreen legibility and fiducial contrast.

SMD vs NSMD: solder mask defined pads

Pad definition is where PCB solder mask choices hit yield hardest.

Solder mask defined pads (SMD) and NSMD are both valid. Problems start when a library mixes them without documenting which BGA or QFN expects which, or when mask swell closes an SMD opening. Confirm with the package datasheet and the assembler, then capture the rule in your PCB design review checklist.

Side-by-side SMD vs NSMD pad definition under green solder mask with copper lands
Side-by-side SMD vs NSMD pad definition under green solder mask with copper lands

Openings, dams, expansion and clearance

Solder mask openings must clear every pad, testpoint and exposed copper you intend to solder or probe. Between pads, the remaining mask strip is the dam. Dams that are too narrow lift or crack in fab; dams that are too wide force mask into the paste area when expansion is wrong.

Typical fab notes include:

Mask swell and misregistration turn a legal dam into a bridge risk. That is why openings belong in DFM review before Gerbers, alongside panelization and via rules from guides like blind and buried vias and thermal vias.

Tented, plugged and open vias

Via treatment under PCB mask is another process choice:

Tenting every via by default can hide issues on dense BGA breakouts and via-in-pad designs. Coordinate mask and via fill with your fab the same way you plan controlled impedance stackups: written notes, not assumptions.

Common PCB solder mask mistakes

Panelization choices also interact with mask: edge copper and break tabs need clear mask rules so rails and fiducials stay inspectable (PCB panelization guide). Local copper and decoupling pads need the same opening discipline as any other SMT land (decoupling capacitor placement).

Where AI and DFM checks help

Most solder mask failures are geometric: swell that closes openings, dams below capability, silkscreen on copper, vias that should not be tented, SMD/NSMD mismatches on fine pitch. An AI assisted DFM pass can flag those while copper and mask artwork can still change, instead of after the first fab lot.

That is the IntelCAD angle on PCB solder resist: not another glossary of green ink, but a decision guide that ties LPI vs dry film, pad definition, tenting and dams to manufacturability checks before Gerbers leave.

FAQ

What is solder mask on a PCB?

Solder mask (solder resist) is the polymer coating that covers copper except where pads, vias or other openings must stay exposed for soldering, probing or plating. It prevents bridges, protects copper and sets board color.

What is the difference between LPI and dry film solder mask?

LPI (liquid photoimageable) is coated as a liquid, exposed and developed; it is the usual production choice for fine openings. Dry film is laminated as a sheet and suits builds that need more uniform thickness or thicker copper coverage.

What are SMD and NSMD pads?

SMD (solder mask defined) pads use a mask opening smaller than the copper, so the mask sets the solderable size. NSMD (non-solder-mask-defined) pads leave copper smaller than the opening, so copper sets the land. Package and assembler rules decide which to use.

Should vias be tented with solder mask?

Tent vias when you want coverage and lower cost. Leave them open for probing or when tenting is unreliable. Use plugged or filled vias for via-in-pad, sealing or when paste must not enter the barrel. Confirm with fab notes.

Which solder mask color should I choose?

Green is the default for inspection contrast. Other colors work for branding or optics, but check AOI, silkscreen readability and fiducial contrast before you lock the color in fab notes.

Next step

Want mask openings, dams and pad-definition risks flagged while the artwork can still change? Start Your Design with IntelCAD for AI assisted PCB design and manufacturability checks.

Image alt-text ideas:

  1. “Top-down PCB with green solder mask, exposed copper pads and vias in a clean technical diagram”
  2. “Side-by-side SMD vs NSMD pad definition under green solder mask with copper lands”
  3. “Cross-section concept of LPI solder mask coating over copper traces with pad openings”

Design your next board by describing it.

Start Your Design