IntelCAD team

PCB Design Review Checklist: 40 Checks Before Gerbers

A practical PCB design review checklist: 40 checks across schematic, placement, routing, power, DFM and fab files to run before you send Gerbers.

Green PCB with IC, decoupling parts and copper checklist shapes for a PCB design review checklist

Short answer: A PCB design review is a structured check of the schematic, placement, routing, power and fab files. Run it before layout freeze and again before you release Gerbers so pin errors, broken return paths, thermal gaps and file mismatches are caught while changes are still cheap. Use a printed checklist at each gate, not a last minute glance.

When to run a PCB design review

A useful PCB design review is not a single meeting at the end. Three passes catch different classes of problems:

  1. Schematic review. Confirm connectivity, pin mapping, power architecture, protection and part choices while changes are still cheap.
  2. Layout review. Once placement and routing are mostly done, check return paths, impedance nets, clearances, thermal paths and mechanical fit before layout freeze.
  3. Pre fab release review. Before you send Gerbers, confirm the Gerber, drill, BOM and pick and place files tell the same story, and that the design stays inside your fabricator’s capabilities.

Skipping any of these three turns small schematic errors into costly board spins. A short design review checklist at each gate is faster than fixing a dead prototype.

Schematic checks

Start with the netlist truth. Every power rail should have a clear voltage, a known source and a path for return current. Confirm decoupling capacitor placement is planned for each IC power pin family, not left as a generic “add caps later” note.

For a deeper net-by-net pass before layout, use the schematic review checklist.

Pin mapping must match the datasheet for every connector, MCU, FPGA and mixed signal part. Check pull ups and pull downs on open drain lines, I2C, reset lines and configuration straps. Reset and boot pins need defined levels at power up so the board does not come up in the wrong mode.

At every external connector, ask what happens on ESD, hot plug and reverse polarity. TVS diodes, series impedance and grounding of shields belong in the schematic, not as a late layout afterthought. Component ratings and derating matter for voltage, current, temperature and lifetime. Finally, check part availability and lifecycle so you are not releasing a board around an obsolete or end of life part.

Placement checks

Good PCB layout guidelines start with placement, not with the first trace. Place critical parts first: clocks, high speed interfaces, power stages, analog front ends and connectors that fix the mechanical outline. Put decoupling capacitors close to the pins they serve, with short paths to the reference plane.

Hot parts need a path for heat and airflow. Leave keep out zones that match the enclosure, standoffs, battery packs and cable bend radii. Connectors should land where the cable actually exits the product. Add test points for power rails, ground, programming interfaces and critical nets while there is still room. A rushed placement pass is the most common reason a PCB layout review later feels impossible.

Routing and signal integrity checks

Controlled impedance nets need a defined stackup and a target impedance before you route them. Link your review to the controlled impedance and PCB stackup decisions already on the board. Every high speed return current needs a continuous path on the adjacent reference plane. Plane splits under those nets force the return to detour and radiate.

Size power and high current nets for the real current using a PCB trace width check, not a default signal width. Route differential pairs with matched length and consistent spacing. For high voltage nets, clearances and creepage must meet the product safety rules, not only the fabricator’s minimum spacing. Ground planning belongs in this pass as well; see the PCB ground plane design guide when return paths look broken.

Power and thermal checks

Power review is more than “the regulator is placed”. Confirm every power net’s copper can carry its worst case current, including startup and fault. Use the PCB trace width calculator as a quick sanity check, then look at via count when a power path changes layers.

Place thermal vias under exposed pads of hot parts and tie them to enough copper on other layers. Copper pours help both current and heat, but they still need solid connections to planes and to the load. Estimate voltage drop on low voltage rails over the real path length. A rail that is thermally fine can still starve a processor if the drop is large.

DFM and fab file checks

A PCB checklist that stops at the layout window is incomplete. Align design rules with your fabricator’s capabilities for minimum trace, space, drill and annular ring. Confirm solder mask openings and silkscreen will not crowd pads or hide polarity marks. Think about panelization if the board is small or needs rails for assembly.

Before release, open the Gerber, drill, BOM and pick and place files together. Layer names, drill sizes, reference designators and quantities must match. The PCB DFM and Gerber files guides cover the common ways these files disagree. A clean layout with a wrong drill or BOM still builds the wrong board.

Printable PCB design review checklist

Use this PCB design review checklist as a printable PCB design checklist before layout freeze and again before fab release. Keep a dated sign off for each pass.

Schematic

  1. Every power rail has a named voltage, source and return path.
  2. Decoupling is defined for each IC power pin family.
  3. Connector and IC pin mapping matches the datasheets.
  4. Pull ups and pull downs are present on open and strap pins.
  5. Reset and boot pins have defined power up levels.
  6. ESD and connector protection is drawn for every external interface.
  7. Component voltage, current and temperature ratings include derating.
  8. Part lifecycle and availability are acceptable for the build.

Placement

  1. Clocks, high speed, power and analog blocks are placed first.
  2. Decoupling capacitors sit close to the pins they serve.
  3. Hot parts have a clear thermal and airflow path.
  4. Connectors match the mechanical outline and cable exits.
  5. Keep outs cover standoffs, enclosure walls and moving parts.
  6. Test points exist for rails, ground, programming and critical nets.

Routing and signal integrity

  1. Controlled impedance nets have a stackup and target impedance.
  2. High speed returns ride a continuous adjacent reference plane.
  3. Plane splits are kept out from under sensitive nets.
  4. Trace width matches current on every power and heater net.
  5. Differential pairs keep spacing and length matching.
  6. High voltage clearance meets the product rule set.
  7. High voltage creepage meets the product rule set.
  8. Ground and return stitching is present where planes change.

Power and thermal

  1. Worst case current, not average current, sets copper width.
  2. Thermal vias sit under exposed pads of hot parts.
  3. Copper pours tie solidly into planes and loads.
  4. Voltage drop on low voltage rails is checked over path length.
  5. Layer transitions on power nets use enough parallel vias.
  6. Plane copper weight matches the current and thermal plan.

DFM and fab files

  1. Design rules sit inside the chosen fabricator’s capabilities.
  2. Annular ring meets the fabricator’s minimum.
  3. Drill sizes and aspect ratios are within fab limits.
  4. Solder mask openings clear pads without slivers.
  5. Silkscreen is readable and clear of pads and vias.
  6. Panelization and board outline are agreed with assembly.
  7. Gerber layer set matches the intended stackup.
  8. Drill file matches pad and via locations in the Gerbers.
  9. BOM reference designators and quantities match the schematic.
  10. Pick and place file matches the BOM and footprint rotations.
  11. Fabrication notes call out stackup, finish and special drills.
  12. A dated sign off records who completed this PCB review.

Common review mistakes

Three mistakes show up often. The first is reviewing only the layout. Schematic pin errors, missing pull ups and wrong boot straps survive a beautiful copper pour. The second is skipping the BOM. A layout that passes DRC still fails if the BOM has the wrong package, an obsolete MPNs or quantities that do not match placement. The third is having no sign off record. Without a dated checklist and an owner, the same issues return on the next spin and nobody can tell which PCB design rules were actually checked.

Where AI helps

A manual PCB layout review jumps between the schematic, datasheets, layout, spreadsheets and distributor pages. Context gets lost, and availability or derating checks are easy to skip under schedule pressure. An AI assisted flow can keep the parts list, availability, lifecycle flags and rule checks in one place while you walk the schematic and layout. It does not replace engineering judgment on stackup, return paths or safety clearances, but it reduces the chance that a part or rule falls through the cracks before Gerbers go out.

FAQ

What should a PCB design review checklist include?

A practical PCB design review checklist covers schematic, placement, routing and signal integrity, power and thermal, and DFM plus fab files. The printable list above has 40 checks across those groups, ending with a dated sign off.

When should you do a PCB design review?

Run a schematic review early, a layout review before layout freeze, and a pre fab release review with the Gerber, drill, BOM and pick and place files open. Waiting until Gerbers are almost sent leaves expensive mistakes in place.

What is the difference between a schematic review and a layout review?

A schematic review checks connectivity, pin mapping, protection, ratings and part choices. A layout review checks placement, return paths, impedance nets, clearances, thermal paths and mechanical fit on the board.

Who should review a PCB design?

The designer should run the checklist first, then a second engineer or reviewer who did not draw every net should walk the same list. Include mechanical and manufacturing input on connectors, keep outs and fab notes before release.

Can AI review a PCB design?

AI can help by checking parts, availability, lifecycle and design rules in one place instead of jumping between datasheets and spreadsheets. Engineers still own stackup, return path and safety decisions, and they still sign off the checklist.

Next step

Ready to catch part, availability and rule issues earlier in your PCB design checklist flow? Start Your Design with IntelCAD for AI assisted PCB design and component selection.

Design your next board by describing it.

Start Your Design