IntelCAD team

PCB Fiducial Marks: Size, Placement and Design Rules

PCB fiducial marks explained: global, local and panel fiducials, recommended size and clearance, placement rules, and common mistakes that stop assembly.

Pick-and-place camera aligning on a round copper PCB fiducial mark next to a fine-pitch chip footprint

Short answer: A PCB fiducial is a small, bare copper mark, usually a round dot about 1 mm across inside a clear solder-mask opening, that a pick-and-place machine’s camera uses to find the exact position, rotation and stretch of a board before placing parts. Use at least three global fiducials per board side in an asymmetric pattern, add local fiducials near fine-pitch parts such as BGAs and 0.5 mm pitch QFPs, and put panel fiducials on the assembly rails. Keep them flat, unmasked, free of silkscreen and away from the board edge.

Pick-and-place camera aligning on a round copper PCB fiducial mark next to a fine-pitch chip footprint
Pick-and-place camera aligning on a round copper PCB fiducial mark next to a fine-pitch chip footprint

What is a fiducial on a PCB?

In general, a fiducial is a reference point that a measuring or vision system can lock onto. On a printed circuit board, fiducial marks are those reference points for assembly. Every board is slightly off from its CAD data: the panel sits a little differently in the machine, the laminate shrinks or stretches, and the copper image is never perfectly registered. The assembly machine photographs the fiducials, compares their measured positions with the coordinates in the placement file, and corrects every placement for offset, rotation and scale.

Without good fiducial points, the machine has to rely on the board edge or tooling holes, which are far less accurate. That is usually fine for large passives, but not for a 0.4 mm pitch BGA or a fine-pitch QFN. Fiducials are also used by solder paste printers and automated optical inspection (AOI) to line up the stencil and the inspection images.

Types of PCB fiducials

There are three kinds, and most production boards use at least two of them.

If components are placed on both sides of the board, each side needs its own set of global fiducials, because the machine only sees the side facing its camera.

Recommended PCB fiducial size and clearance

Most assemblers ask for something close to this. Always check your assembler’s own guidelines, because vision systems and lighting vary.

FeatureTypical value
Fiducial shapeSolid filled circle of bare copper
Fiducial diameter1.0 mm is the most common; about 1 to 3 mm is generally accepted
Clear area (no mask, copper, silkscreen)At least twice the dot diameter, for example a 3 mm opening around a 1 mm dot
Distance from board or panel edgeSeveral millimeters, clear of conveyor rails and clamps; many assemblers ask for 3 to 5 mm or more
Count per side3 global, plus 2 local per critical fine-pitch part

The clear area is what gives the camera contrast. A bright copper dot surrounded by dark, matte laminate is easy to find. A dot crowded by traces, mask slivers or silkscreen is not.

PCB fiducial placement rules

  1. Use an asymmetric pattern. Put the three global fiducials at three corners but not in a perfectly symmetric layout, so a board loaded rotated 180 degrees is rejected instead of placed wrongly.
  2. Spread them out. The farther apart the marks are, the more accurately the machine can calculate rotation and scale.
  3. Keep them off the edges and rails. Edge clamps, conveyor belts and V-scores can hide or damage fiducials near the board edge.
  4. Keep mask, silkscreen and copper out of the clear area. Make sure the solder mask opening is defined around the fiducial and that silkscreen text and outlines stay well clear.
  5. Do not paste them. Fiducials need no solder paste. Remove them from the paste layer so they stay flat and clean.
  6. Make them part of the footprint or library. Local fiducials belong in the BGA or QFP footprint, and global fiducials should be placed components with reference designators, so they appear in the pick-and-place file instead of being loose copper.
  7. Check the finish. Flat finishes such as ENIG give a clean, consistent target. Uneven HASL can make fiducials look domed or irregular to the camera; see our HASL vs ENIG guide if you are choosing.
  8. Avoid nearby look-alikes. Round test points or vias of similar size close to a fiducial can confuse the vision system.

Common fiducial mistakes

Add a fiducial line to your PCB design review checklist and your DFM review, and most of these are caught before the board reaches the assembler.

Where AI and DFM checks help

Fiducial problems are almost always geometry and data problems: a dot that is too close to the edge, a clear area broken by mask or silkscreen, a symmetric pattern, a fine-pitch part with no local marks, or a fiducial that is in the copper but not in the placement file. These are easy to check automatically and easy to miss by eye. An AI-assisted DFM pass reads the copper, mask, silkscreen and paste layers together with the assembly data, finds every fiducial, and flags the ones the assembler’s camera will not see or the parts that need local marks, before you order the board.

That is the IntelCAD angle on fiducials: not a generic rule list, but a check tied to the actual footprints, layers and assembly files on your board.

FAQ

What is a fiducial on a PCB?

A PCB fiducial is a small bare copper mark, usually a round dot, that assembly machines use as an optical reference to correct the board’s position, rotation and scale before placing components.

How many fiducials does a PCB need?

Use three global fiducials on each side that has components, in an asymmetric pattern near the corners. Add two local fiducials diagonally across each fine-pitch part such as a BGA or 0.5 mm pitch QFP.

What size should a PCB fiducial be?

A 1 mm diameter copper dot is the most common choice, with a clear area free of solder mask, copper and silkscreen of at least twice the dot diameter. Check your assembler’s exact requirement.

Should fiducials be covered by solder mask?

No. The fiducial and its clear area should be exposed so the camera sees bright copper against bare laminate. Leave fiducials off the solder paste layer as well.

What is the difference between global and local fiducials?

Global fiducials align the whole board side. Local fiducials sit beside a single fine-pitch component and correct the small remaining error at that location.

Next step

Want every fiducial on your board checked against your assembler’s rules before you order? Start Your Design with IntelCAD for AI assisted PCB design and manufacturability checks.

Design your next board by describing it.

Start Your Design