IntelCAD team

Silkscreen PCB Guide: Legend, Text Size and Colors

Silkscreen PCB guide: what the legend is, text size, colors, polarity marks, reference designators, and how AI/DFM catches silkscreen-on-pad before fab.

Top-down green PCB with white silkscreen outlines, polarity marks and pin-1 indicators around copper pads

Short answer: Silkscreen on a PCB (also called the legend or silk screen layer) is the printed ink that shows reference designators, polarity marks, pin-1 indicators and outlines so people and machines can assemble and debug the board. A good silkscreen PCB design picks a readable text size and stroke, a color that contrasts with the solder mask, and keep-out from pads, vias, holes and fiducials. Most production boards use white legend ink on green mask, applied by liquid photoimageable (LPI) legend, traditional screen printing or inkjet.

Top-down green PCB with white silkscreen outlines, polarity marks and pin-1 indicators around copper pads
Top-down green PCB with white silkscreen outlines, polarity marks and pin-1 indicators around copper pads

What is silkscreen on a PCB?

When people ask what is silkscreen PCB artwork, they mean the identification layer printed after solder mask. It does not carry current. It tells the assembler and the technician which part goes where, which way it faces, which pin is pin 1, and which revision you are holding.

Silkscreen on PCB layers usually appear as top and bottom legend Gerbers (or matching ODB++ steps), plotted in epoxy or similar ink. Call it silkscreen, silk screen, legend or nomenclature; the design job is the same. Treat screen printing PCB artwork as a DFM layer, not decoration added after routing is frozen.

What belongs on the silkscreen (legend) layer

A useful silkscreen circuit board legend includes only what someone still needs after the parts are placed:

Leave off logos that crowd fine-pitch parts, warnings that land on pads, and courtyard-sized outlines copied from a library. If density is too high for readable text, put the full map on the assembly drawing and keep only polarity and pin 1 on the board. That choice belongs in the same PCB design review checklist as courtyard and footprint checks.

Silkscreen PCB text size and line width

PCB silkscreen text size is a process window, not a font preference. Many fabricators quote a minimum character height around 0.8 mm (about 32 mil) and a minimum stroke around 0.15 mm (about 6 mil). 1.0 mm height with a slightly heavier stroke is easier for humans and cameras when there is room. Stroke fonts (plotted as centerline width) usually survive fab better than filled TrueType outlines that thin out or flood.

PCB silkscreen thickness of the ink itself is a fab process choice, often in the tens of micrometers. You control whether the artwork is legal: height, stroke and clearance. Ask your shop for plotted minimums before you lock a 0.6 mm refdes on a dense connector row. If a designator cannot meet those limits without sitting on a pad or via, move it or drop it.

Silkscreen colors and contrast with solder mask

White legend on green solder mask remains the default because contrast is high for both eyes and AOI. Yellow, black, red and other PCB silkscreen colors are available, but contrast against the mask matters more than branding.

Watch black silk on dark mask, white silk on pale mask, and any color that hides fiducials or polarity marks under factory lighting. Lock silkscreen color in the same fab notes as mask color and finish, the way you lock a PCB stackup.

Polarity marks, pin 1 and reference designators

Most assembly escapes blamed on “the silk” are orientation errors. A silkscreen PCB that shows every refdes but hides pin 1 on a fine-pitch IC, or puts the plus sign under a tall capacitor, has failed its main job.

Put pin 1 at the package as a dot, bevel or notch that can still be seen after placement. Mark polarized parts beside the body, not in the paste area. Keep reference designators unique and matching the BOM and pick-and-place file. Do not mirror designators on the top layer; do expect the bottom legend Gerber to be mirrored unless your shop says otherwise.

Libraries that ship an outline with no pin-1 mark, or that place a designator in the center of a QFN, need a pass before layout freeze. Use the same discipline you use when you review decoupling capacitor placement.

Keep-off: pads, vias, holes and fiducials

Silkscreen ink on copper you intend to solder is contamination. It can cause poor wetting, tombstoning on small chip parts, and inspection failures. The usual keep-off is about 0.15 mm to 0.2 mm (6 to 8 mil) from pad edges, though your fab’s spec wins.

Keep silk off SMT and through-hole pads, probe-clean testpoints, untented vias and via-in-pad sites (see blind and buried vias and thermal vias), tooling holes, and fiducials so cameras see a clean target on the panel.

Side-by-side silkscreen keep-off: white legend overlapping a copper pad versus a clear gap around the pad
Side-by-side silkscreen keep-off: white legend overlapping a copper pad versus a clear gap around the pad

Many CAD tools can clip silk from pads automatically. Use that, then check what the clip deleted: a polarity mark that vanished is not a successful cleanup.

How silkscreen is applied

Three processes show up most often in production silk screening PCB work:

ProcessHow it is appliedStrengthsTradeoffs
Liquid photoimageable (LPI) legendPhotoimaged ink, similar in spirit to LPI maskFiner features, good registrationNot every shop runs it; cost can be higher
Traditional screen printingInk pushed through a mesh stencilCommon, inexpensive, easy to seeCoarser resolution; small text and thin strokes disappear
Inkjet legendDirect printed inkFlexible for data, revisions or serializationInk and adhesion vary by shop; artwork still must be legal

The PCB silkscreen process you get is whatever the fab qualified. If you need 0.8 mm text in a tight row, ask whether they screen-print or photoimage the legend before you promise that density.

Common silkscreen PCB mistakes

These are DFM issues, not cosmetic nits. They show up in assembly programming, first-article inspection and field debug.

Where AI and DFM checks help

Most silkscreen failures are geometric and therefore checkable: ink over pads, strokes below capability, designators colliding with courtyards, missing pin-1 on a polarized footprint, silk on a fiducial, or a color note that fights the mask. An AI-assisted DFM pass can flag those while the legend can still move, instead of after the first assembled lot comes back with reversed parts.

That is the IntelCAD angle on silkscreen PCB design: not another glossary of white ink, but a decision guide that ties text size, contrast, polarity and keep-off to checks before Gerbers leave.

FAQ

What is silkscreen on a PCB?

Silkscreen (the legend or silk screen layer) is printed ink that identifies parts, polarity, pin 1, outlines and board markings. It is applied after solder mask and does not form electrical connections.

What is the difference between silkscreen and solder mask?

Solder mask is the coating that protects copper and defines where solder may land. Silkscreen sits on top of the mask (and clear of pads) so people and machines can read the board. Mask controls soldering; silk controls identification.

What text size should PCB silkscreen use?

Use your fabricator’s minimums. A common starting point is about 0.8 mm character height and 0.15 mm stroke, with 1.0 mm height when space allows. If text cannot meet those limits without hitting a pad, move or remove it.

What color should PCB silkscreen be?

White on green mask is the most readable default. Other colors work when contrast stays high. Avoid black-on-black or white-on-white combinations that hide polarity marks and fiducials.

Can silkscreen go on pads?

No. Ink on a solderable pad is contamination and a DFM defect. Keep roughly 0.15 mm to 0.2 mm clearance from pads, and keep silk off testpoints, fiducials and features that must stay clean.

Next step

Want silkscreen-on-pad, missing polarity marks and unreadable refdes flagged while the legend can still move? Start Your Design with IntelCAD for AI assisted PCB design and manufacturability checks.

Design your next board by describing it.

Start Your Design